Production Performance Brief
How to Compare Water Bottling Line Performance Offers
Turn a quoted BPH figure into a production requirement that purchasing and engineering can both check before an order.
Direct answer
What should a water bottling line performance specification include?
Review point 01
Write the output requirement before comparing prices
State the product, bottle drawing, neck and cap, label, bottles per pack and final counting point. Separate new equipment, retained machines and buyer-supplied connections. This page compares the production promise behind an offer, not a generic plant budget.
- Define accepted bottles or complete packs per scheduled shift, not only the maximum running speed.
- List changeovers, cleaning and material replenishment included in that window.
- State point-of-use water, power and compressed-air conditions without substituting installed utility totals.
Review point 02
Worked comparison: two BPH figures that mean different things
Illustrative comparison, not actual supplier offers: the buyer needs 40,000 accepted bottles in an 8-hour scheduled window. Offer A states 6,000 BPH during a 30-minute filler demonstration. Offer B states an average of 5,500 accepted bottles/h over the complete 8-hour connected test on the agreed pack. B describes 44,000 accepted bottles on its stated basis; A does not yet establish a shift output.
- Do not extrapolate the short filler demonstration to 48,000 accepted bottles.
- Request the same connected test, time boundary and reject rules from both bidders.
- Neither the illustration nor a written claim replaces test evidence or the final agreement.
Review point 03
Separate a deviation from an optional extra
Use comply, deviate, excluded, optional and buyer-supplied against each requirement. A missing packer recovery test is a verification gap; an optional packer is a scope difference. Both can change the value of a quotation even if its headline price is lower.
- Name the machine or party responsible for each material, conveyor and control handoff.
- Record format parts, recipes, drawings, software access and operator documentation needed for the agreed SKU.
- Price a change only after its effect on the common output basis is clear.
Review point 04
What to send for a performance review
Send a non-confidential requirement sheet and relevant proposal extracts, bottle/pack details, required output and unresolved deviations. For an existing line, include its measured output and the equipment to retain. Agree the final supply and performance conditions in the project quotation.
- FAT: establish what can actually be verified before shipment.
- SAT: test the installed connections, utilities and accepted output on site.
- Define pass criteria, count reconciliation, allowed interventions and how an unresolved test is corrected and repeated.
| Comparison item | Offer A | Offer B | Buyer decision |
|---|---|---|---|
| Rate and duration | 6,000 BPH; 30-minute filler run | 5,500 accepted bottles/h; 8-hour connected window | Request one common duration and counting boundary. |
| Shift quantity | Not established by the short test | 5,500 × 8 = 44,000 on the stated illustrative basis | Verify the underlying counts; do not treat nominal speed as good output. |
| Bottle and pack | Must be confirmed | Agreed reference format in this example | Match drawing, closure, label and complete pack. |
| Price comparison | Commercial scope to confirm | Commercial scope to confirm | Compare commercial scope only after performance deviations are visible. |
Catalog equipment evidence
See the machines behind this production-line question.
These Allot Tech catalog references connect the technical explanation to physical equipment. Each caption identifies the capacity, interface or acceptance evidence to confirm.
Connected water bottling line
Use the complete-line view to mark machine boundaries, transfer points, utilities, controls and output counting locations.
Review this interface basis
Water bottling production process flow
Separate water preparation, bottle supply, filling, decoration and packing, then compare every node on one output basis.
Review this interface basis
Rinse-fill-cap center
State filler BPH with the reference bottle, product, cap, test window and accepted-output counting point.
Review this interface basis
End-of-line packing system
The packer is one connected capacity node; pack pattern, cycle, bottle behavior and discharge flow set the usable rate.
Review this interface basisSource: Allot Tech Beverage Bottling Catalog 2026. Images are representative equipment references; final models and configurations remain project-specific.
Questions before specification
Frequently asked questions
Answers are planning guidance. Project requirements and performance remain subject to confirmed data and agreements.
Is the higher-BPH quotation always the better offer?
No. Different formats, test windows, equipment boundaries and reject definitions can make the figures incomparable. Normalize those conditions before ranking offers.
Can the specification guarantee that every bottle size runs at one speed?
No. List each production SKU and its confirmed performance conditions. Bottle volume alone does not establish neck, handling, label or pack compatibility.
Do I need to upload a complete confidential quotation?
No. Begin with non-confidential technical extracts and redact unrelated commercial or personal information. The request form also accepts a short description without an attachment.
Next buyer step